Best Way to Get Corrosion Off Car Battery

Download Article

Download Article

Many drivers experience difficulty starting their vehicles at some point or another. Sometimes, a major part is to blame, but a lot of times this frustrating event is caused by buildup on the battery terminals. Learning how to clean corroded car battery terminals will avoid unnecessary expenses and worry.

1. 1

   Determine the terminal configuration of your battery. There are two types.^[1]

   • If the terminals are on the side, you will need a 5/16-inch (8 mm) wrench to loosen both cable nuts.
   • If the terminals are on top of the battery, you will need either a 3/8-inch (10 mm) or 1/2-inch (13 mm) wrench.

2. 2

   Make sure your car is turned off. This will reduce the likelihood of accidentally grounding the cables.

3. 3

   Loosen the nut on the negative (-) cable clamp. Unfasten the cable from the post.^[2]

   • Do the same for the positive (+) cable. If you have trouble removing either cable, attempt to twist them while pulling up at the same time.

4. 4

   Examine the battery for cracks that may be leaking acid. If any are found, you need to replace the battery.

5. 5

   Check the battery cables and clamps for tears. If a large rip is found, you may have to replace these parts.

6. 6

   Mix 1 tablespoon (15 ml) of baking soda with 1 cup (250 ml) of very hot water. Dip an old toothbrush into the mixture and scrub the top of the battery to remove corrosion buildup.^[3]

   • You can even dip the ends of the battery cables in hot water to dissolve any corrosion on the cable ends themselves.

7. 7

   Use the toothbrush to scour the battery clamps and posts. Remember to soak your brush in the baking soda solution as much as needed.

8. 8

   Rinse the battery and cables with cool water. Make sure all the baking soda and corrosion is washed away. Dry the battery and clamps with a clean cloth.

9. 9

   Lubricate all exposed metal on battery terminals, posts and clamps. Use petroleum jelly or a commercial battery terminal protection spray.^[4]

10. 10

    Reattach the positive (+) cable clamp to the proper terminal. Tighten the nut with your wrench.

    • Repeat with the negative (-) clamp. Test if terminals are tight enough by twisting each one by hand.

1. 1

   Keep a pair of gloves and correct-size wrench in your trunk or back seat.

2. 2

   Loosen each terminal slightly with your wrench. Do not entirely remove the cables.

3. 3

   Pour cola over the battery from the center outward in one direction. Repeat going in the opposite direction.

4. 4

   Allow it to soak for two minutes, then rinse off with water. Tighten the terminals and try to restart the car.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

• You can purchase a battery cleaner spray. Some include an acid detector in the formula. These tend to be less time-consuming, but you must read the directions on the bottle, because each one is different.

• You can use a battery terminal brush or sandpaper if the buildup is too heavy for a toothbrush.

• The negative cable should always be removed first and attached last to prevent arcing.

• Always wear protective gear.

• Remove all jewelry before starting work. Rings and bracelets can become grounded or get caught on engine parts.

Things You'll Need

• Goggles or safety glasses
• Latex or nitrile gloves
• Wrench: 5/16-inch (8 mm), 3/8-inch (10 mm) or 1/2-inch (13 mm)
• Toothbrush
• Baking soda
• Water
• Cup or bucket
• Terminal brush (optional)
• Petroleum jelly or battery terminal protection spray

About This Article

Article SummaryX

Before you clean corroded car battery terminals, be sure your car is turned off so you don't ground the cables. Then, use a wrench to loosen the nuts on the cable clamps, and unfasten the cables from the posts. Next, mix 1 tablespoon of baking soda with 1 cup of very hot water. Dip an old toothbrush into the mixture, then remove any corrosion by scrubbing the top of your battery and the battery clamps and posts. Finally, rinse the battery and cables with cool water and dry them completely before refastening them. For more from our Master Mechanic reviewer on cleaning corroded car battery terminals, including how you can use a soda in an emergency, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 1,019,935 times.

Did this article help you?

Best Way to Get Corrosion Off Car Battery

Source: https://www.wikihow.com/Clean-Corroded-Car-Battery-Terminals

Share this post